Proxmark3 community
Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Announcement
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
Pages: 1
#1 2014-09-14 05:10:21
- n3rd
- Contributor
- Registered: 2013-03-30
- Posts: 38
Going to try again
See my previous posts for failed attempts at getting a PM3 running, but I am going to try again. It looks like the latest files are now on Github.
Is this the right place to start? -> https://github.com/Proxmark/proxmark3/wiki/Windows
Offline
#2 2014-09-14 07:00:31
- asper
- Contributor
- Registered: 2008-08-24
- Posts: 1,409
Re: Going to try again
A good place to start using pm3 under windows 
Offline
#3 2014-09-14 14:53:35
- n3rd
- Contributor
- Registered: 2013-03-30
- Posts: 38
Re: Going to try again
Right, assuming I was going to use Win 7 x64 (I may try with Linux again too as I have just upgraded to the latest Redhat LTS version)
Offline
#4 2014-09-15 04:16:05
- n3rd
- Contributor
- Registered: 2013-03-30
- Posts: 38
Re: Going to try again
Step 3:
Download "ProxSpace-20100226-r390.7z" from: http://code.google.com/p/proxmark3/downloads/list
That file does not exist at that URL.
Should I be downloading "ProxSpace-130613.7z" or something else?
Last edited by n3rd (2014-09-16 00:08:14)
Offline
#5 2014-09-16 00:07:58
- n3rd
- Contributor
- Registered: 2013-03-30
- Posts: 38
Re: Going to try again
Also, reading ahead:
Download the Proxmark drivers ("ProxSpace-Driver-Current.7z") from here: http://code.google.com/p/proxmark3/downloads/list
[NOTE: if your proxmark has a firmware greater than r654 (old google code naming) you will need the new CDC serial drivers contained in pm3-bin-756 (cdc+lua).rar that is also available in the above link - more info in this paragraph]
How do I tell what firmware revision my PM3 has before I get it installed? I bought it online from China last March and I am not sure the seller is even still around.
Offline
#6 2014-09-20 16:53:04
- n3rd
- Contributor
- Registered: 2013-03-30
- Posts: 38
Re: Going to try again
Step 3:
Download "ProxSpace-20100226-r390.7z" from: http://code.google.com/p/proxmark3/downloads/list
That file does not exist at that URL.
Should I be downloading "ProxSpace-130613.7z" or something else?
Hi folks - any advice? I want to get this right the first time and the documentation is pointing to a nonexistent file...
Offline
#7 2014-09-21 03:43:36
- marshmellow
- Contributor
- From: US
- Registered: 2013-06-10
- Posts: 2,302
Re: Going to try again
Offline
#8 2014-09-21 21:33:25
- n3rd
- Contributor
- Registered: 2013-03-30
- Posts: 38
Re: Going to try again
Thank you!
I had seen that post but since the 1st one in the thread was from March 2013, I thought it was old. I see now it has been kept updated. I guess I will try with Windows first maybe Linux later.
I have downloaded PM3-bin-0.0.5. I still am not sure, however how to proceed. There are drivers for the 'new serial interface' and the 'old usb interface'. How do I know which one to use? I don't know what firmware is flashed on my PM3.
Offline
#9 2014-09-21 23:01:43
- asper
- Contributor
- Registered: 2008-08-24
- Posts: 1,409
Re: Going to try again
The incorrect driver won't install so you can try without fear. If you have old libusb you should consider to update to the new cdc-serial firmware because libusb is no more supported.
Offline
Pages: 1