[solved] hw ver for iceman's latest fork?

phiber · 2016-10-16 17:35:45

Hi iceman,

i am trying to flash your fork based on your information on the website.
I managed to compile your latest github fork/pull with no errors in windows.

First i flashed the bootrom and it went well with the command: flasher com3 -b bootrom.elf

But when i tried to flash the fullimage.elf, with the command: flasher com3 -b fullimage.elf

the first part it detected the proxmark and issued the boot-flash start commend, the pm rebooted. but at this point, i can see the usb device restarted. but the program just stalled while waiting for the proxmark to reappear on com3.

i waited but it did not return, so i checked device managed and realised that in boot-flash mode, someone the device attached to com4! LOL

no idea why, but so i changed the new device to com3 and the fullimage flash went on well.

Here is my hw ver:

Prox/RFID mark3 RFID instrument
bootrom: Version information not available
os: Version information not available
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at 9: 8: 8

uC: AT91SAM7S256 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 256K bytes. Used: 215983 bytes (82). Free: 46161 bytes (18).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory

-------------------

Can i ask if that is correct to not show any bootrom and os version?

tried read and cloning a viking id and HID id and both went fine, so can i say that my pm3 is NOT screwed up by a possible bad flash or something?

Thanks!!

Last edited by phiber (2016-10-17 14:16:11)

iceman · 2016-10-16 20:27:29

I don't know if you have pulled the latest source and flashed but below is an excert from my "versions".
Flashing the fullimage shall not be used with "-b" command, which you seem to do.

Compiled / flashed on MINGW/WIN7 environment.

pm3 --> hw ver
[[[ Cached information ]]]

Prox/RFID mark3 RFID instrument
bootrom: iceman/master/release-build(no_git)-suspect 2016-10-08 12:39:55
os: iceman/master/release-build(no_git)-suspect 2016-10-13 16:17:50
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at  9: 8: 8

uC: AT91SAM7S256 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 256K bytes. Used: 217336 bytes (83%). Free: 44808 bytes (17%).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory

phiber · 2016-10-17 02:21:59

FYI, i am using the China Proxmark3 Easy Tool, the one with the 256kb memory, which i see if what you are using also.

yups.. i did a git pull and then a make clean then make all.. no errors that i can see..

OOps.. i must have cut and paste wrongly.. now i'm not sure if i did the flash with -b or not! =X

Anyway, i reflashed it with 2.0.0 and this is the hw veR:

proxmark3> hw ver
#db# Prox/RFID mark3 RFID instrument
#db# bootrom: /-suspect 2015-04-02 15:12:04
#db# os: /-suspect 2015-04-02 15:12:11
#db# HF FPGA image built on 2015/03/09 at 08:41:42
uC: AT91SAM7S256 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 256K bytes
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory

Now i reflash with your images with the correct commands, mingw32/win10x64:

Prox/RFID mark3 RFID instrument
bootrom: Version information not available
os: Version information not available
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at 9: 8: 8

uC: AT91SAM7S256 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 256K bytes. Used: 215983 bytes (82). Free: 46161 bytes (18).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory

seems like still the same result..

can you upload a full zip of your latest compiled exe and images to dropbox or somewhere so i can try to flash those and see the results?

Thank you in advance!

Last edited by phiber (2016-10-17 03:54:36)

iceman · 2016-10-17 09:28:30

hm, it could also be that you don't have perl installed. The "mkversions.pl" script generates the needed info.

phiber · 2016-10-17 13:53:48

iceman wrote:

hm, it could also be that you don't have perl installed. The "mkversions.pl" script generates the needed info.

Yes, that might be it! i realised that there were some perl errors.
I got perl installed and this is my hw ver now:

Prox/RFID mark3 RFID instrument
bootrom: iceman/master/v1.1.0-1626-g4ce2037-suspect 2016-10-17 21:10:17
os: iceman/master/v1.1.0-1626-g4ce2037-suspect 2016-10-17 21:11:32
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at  9: 8: 8

uC: AT91SAM7S256 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 256K bytes. Used: 215989 bytes (82). Free: 46155 bytes (18).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory

This is solved! might want to update the wiki at https://github.com/iceman1001/proxmark3 to include perl for windows!

Thanks!

Last edited by phiber (2016-10-17 14:15:37)

iceman · 2016-10-17 16:23:43

there is no wiki on iceman fork, I think you are talking about the readme.md, feel free to update the text to match with your procedure.

zissilia · 2020-11-23 23:27:05

i am sorry i need help i tried to flash the proxmark3 rdv from rdv40-64-20201119- to
pm3-bin r763 and after this is not appear to any com port i try it in linux the same the leds A and C are on and they blinks i tryed to make all the flash and dint respond the boot loader is stuck now what i do? if i wait until the next day i will be fix ? or i must order JTAG and use with J-Link or ST-Link V2 ?

Last edited by zissilia (2020-11-24 20:18:53)

zissilia · 2020-11-24 20:17:15

i dont know to delete posts i tell me to dont spam i did cause the index has many topics and i had 2-3 problems i thought it was better searching and post according to different posts

Last edited by zissilia (2020-11-24 20:19:42)

Proxmark3 community

Announcement

#1 2016-10-16 17:35:45

[solved] hw ver for iceman's latest fork?

#2 2016-10-16 20:27:29

Re: [solved] hw ver for iceman's latest fork?

#3 2016-10-17 02:21:59

Re: [solved] hw ver for iceman's latest fork?

#4 2016-10-17 09:28:30

Re: [solved] hw ver for iceman's latest fork?

#5 2016-10-17 13:53:48

Re: [solved] hw ver for iceman's latest fork?

#6 2016-10-17 16:23:43

Re: [solved] hw ver for iceman's latest fork?

#7 2020-11-23 23:27:05

Re: [solved] hw ver for iceman's latest fork?

#8 2020-11-24 20:17:15

Re: [solved] hw ver for iceman's latest fork?

Board footer